In the Linux kernel, the following vulnerability has been resolved:
sctp: fix auth_chunk_list capacity check in sctp_auth_ep_add_chunkid
sctp_auth_ep_add_chunkid() uses SCTP_NUM_CHUNK_TYPES (20) as the
capacity limit for ep->auth_chunk_list, allowing it to hold up to
20 chunk entries (param_hdr.length up to 24). However, the copy
destination asoc->c.auth_chunks in struct sctp_cookie is only
SCTP_AUTH_MAX_CHUNKS (16) entries (20 bytes). When more than 16
chunks are added, sctp_association_init() memcpy overflows the
destination by up to 4 bytes.
Fix by using SCTP_AUTH_MAX_CHUNKS as the capacity limit, matching
the destination capacity.
In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix deadlock between reset thread and remove
pci_reset_function() acquires device_lock before performing the reset.
pdsc_remove() is called by the PCI core with device_lock already held.
If pdsc_pci_reset_thread() is running when pdsc_remove() is called,
destroy_workqueue() will block waiting for the work to complete, while
the work is blocked waiting for device_lock - deadlock.
Use pci_try_reset_function() which uses pci_dev_trylock() internally.
This acquires both the device lock and the PCI config access lock
without blocking - if either lock is contended, it returns -EAGAIN
immediately. This avoids the deadlock while also ensuring proper
config space access serialization during the reset.
The pci_dev_get/put calls are also removed as they were unnecessary -
the driver-owned workqueue is destroyed in pdsc_remove(), guaranteeing
the work completes before remove returns. The PCI core holds its
reference to pci_dev throughout the entire unbind sequence.
In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix use-after-free on workqueue during remove
In pdsc_remove(), the workqueue is destroyed before pdsc_teardown()
is called. This ordering allows two paths to queue work on the
destroyed workqueue:
1. If pdsc_teardown() -> pdsc_devcmd_reset() times out, the error
path in pdsc_devcmd_locked() queues health_work.
2. A NotifyQ event can trigger the ISR and queue work before free_irq()
is called in pdsc_teardown().
Fix by moving destroy_workqueue() after pdsc_teardown() so the
workqueue outlives every queuer; destroy_workqueue() then flushes any
work still pending.
Draining the queued work also requires ordering the teardown so the
resources that work touches are freed last:
- In pdsc_qcq_free(), after freeing the interrupt, cancel_work_sync()
the queue's work and only then clear qcq->intx, so
pdsc_process_adminq()'s read of qcq->intx for interrupt-credit
return cannot race with the clear.
- Free adminqcq before notifyqcq: the shared adminq ISR is released
when adminqcq is freed, and the adminq work accesses notifyqcq, so
both must be stopped before notifyqcq is freed.
In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix auxiliary device add/del races
Two paths add or delete the same slot (pf->vfs[vf_id].padev): a VF's
pdsc_reset_done() and the PF's devlink enable_vnet/disable_vnet handler.
They serialize on config_lock, but neither guards the slot under it
correctly.
add() registers and stores a new auxiliary device without first checking
the slot, so a second add of an already-populated slot leaks the first
device. del() makes that check outside config_lock, so two concurrent
dels can both pass it; the first clears the slot, and the second
dereferences a NULL pointer.
Check and update the slot under config_lock in both paths.
In the Linux kernel, the following vulnerability has been resolved:
accel: ethosu: Fix element size accounting for cmd stream validation
There are 2 issues with the element size handling in the command stream
validation which result in too small of a size calculated when the
element size is 16/32/64 bits.
For NHWC format, the element size is simply missing from the
calculation.
The bitfield for the element size is different between IFM/IFM2 and
OFM. IFM and IFM2 encode the precision in parameter bits 2:3, while OFM
uses bits 1:2.
In the Linux kernel, the following vulnerability has been resolved:
sctp: validate stream count in sctp_process_strreset_inreq()
When processing a RESET_IN_REQUEST from a peer,
sctp_process_strreset_inreq() derives the stream count from the
parameter length but does not check whether the resulting
RESET_OUT_REQUEST would exceed SCTP_MAX_CHUNK_LEN.
The OUT request header (sctp_strreset_outreq, 16 bytes) is 8 bytes
larger than the IN request header (sctp_strreset_inreq, 8 bytes).
Generally, the IP payload is bounded to 65535 bytes, so the stream
list cannot be large enough to trigger the overflow. However, on
interfaces with MTU > 65535 (e.g., loopback with IPv6 jumbograms), a
stream list that fits within the incoming IN parameter can cause a
__u16 overflow in sctp_make_strreset_req() when computing the OUT
request size, leading to an undersized skb allocation and a kernel
BUG:
net/core/skbuff.c:207 skb_panic
net/core/skbuff.c:2625 skb_put
net/sctp/sm_make_chunk.c:1535 sctp_addto_chunk
net/sctp/sm_make_chunk.c:3695 sctp_make_strreset_req
net/sctp/stream.c:655 sctp_process_strreset_inreq
The local setsockopt path validates the generated reset request size.
However, for an incoming-only reset, it accounts for the smaller IN
request even though the peer must generate an OUT request with the same
stream list. Such a request cannot be completed successfully by the
peer.
Reject peer IN requests whose corresponding OUT request would exceed
SCTP_MAX_CHUNK_LEN. Also tighten the local check so it does not send an
IN request that would require an oversized OUT request from the peer.
In the Linux kernel, the following vulnerability has been resolved:
net: mctp i3c: clean up notifier and buses if driver register fails
mctp_i3c_mod_init() registers the I3C bus notifier and then walks the
existing buses with i3c_for_each_bus_locked(mctp_i3c_bus_add_new, NULL)
before registering the I3C device driver. If i3c_driver_register()
fails, the function returns the error directly, leaving the notifier
registered and every mctp_i3c_bus object created for the existing buses
allocated. The notifier is left pointing into the module that failed to
load and the bus list is leaked.
Mirror the module exit path on this failure: unregister the notifier and
tear down the buses that were added before returning the error.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
In the Linux kernel, the following vulnerability has been resolved:
tipc: fix infinite loop in __tipc_nl_compat_dumpit
cmd->dumpit callback can return a negative errno, causing an infinite
loop due to the while(len) condition. As the loop never terminates,
genl_mutex is never released, and other tasks waiting on it starve in D
state.
Check dumpit's return value, propagate it and jump to err_out on error.
In the Linux kernel, the following vulnerability has been resolved:
cifs: fix cifsFileInfo leak on kmalloc failure in deferred close drain paths
In cifs_close_deferred_file(), cifs_close_all_deferred_files(), and
cifs_close_deferred_file_under_dentry(), when a pending deferred close
is cancelled via cancel_delayed_work(), the subsequent kmalloc_obj() to
add the file to the local processing list may fail under memory pressure.
The loop breaks immediately, but the cancelled work is no longer pending
(it would have called _cifsFileInfo_put()), and the cfile is never added
to file_head for processing. The cifsFileInfo reference and the open
server handle both leak.
Fix by saving the cfile that failed allocation in a local variable,
breaking as before, and calling _cifsFileInfo_put() on it after
releasing the lock. Any files later in the iteration are unaffected
since their deferred work is still pending and will fire normally.
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: guard link STA in decap offload
mt7925_sta_set_decap_offload() iterates over the vif valid_links mask
when updating decap offload state for an MLO station. The station may not
have a link STA for every valid link of the vif, so mt792x_sta_to_link()
can return NULL for a link that belongs to the vif but not to the station.
The function currently dereferences mlink before checking whether the
link WCID is ready. If mlink is NULL, setting or clearing
MT_WCID_FLAG_HDR_TRANS dereferences a NULL pointer.
Skip links without a station link before touching mlink->wcid.
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: guard HE capability lookups
mt7915_mcu_bss_he_tlv() and mt7915_mcu_sta_bfer_tlv() both run after
checking HE support, then dereference the HE PHY capability returned by
mt76_connac_get_he_phy_cap(). That helper can return NULL when no
capability entry matches the vif type.
Fetch the capability before appending the TLV and skip the HE-specific
setup when no matching capability is available.
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: connac: fix possible NULL-pointer deref in mt76_connac_mcu_uni_bss_he_tlv()
mt76_connac_get_he_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it.
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: check pointer returned by mt76_connac_get_he_phy_cap()
mt76_connac_get_he_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it.
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: fix crash in reset link replay
During reset recovery, mt7925_vif_connect_iter() replays firmware state
for links tracked in mvif->valid_links. After MLO link changes or MCU
timeout recovery, the driver bitmap can temporarily contain a link whose
mac80211 bss_conf has already gone away.
This can pass a NULL bss_conf to mt76_connac_mcu_uni_add_dev(), matching
the crash where x1, the second argument, is NULL:
pc : mt76_connac_mcu_uni_add_dev+0x8c/0x1f8 [mt76_connac_lib]
lr : mt7925_vif_connect_iter+0x9c/0x168 [mt7925_common]
x2 : ffffff80a77f6018 x1 : 0000000000000000 x0 : ffffff8099402080
Call trace:
mt76_connac_mcu_uni_add_dev+0x8c/0x1f8 [mt76_connac_lib]
mt7925_vif_connect_iter+0x9c/0x168 [mt7925_common]
mt7925_mac_reset_work+0x264/0x2f8 [mt7925_common]
Skip missing bss_conf entries before replaying the link. Non-MLO AP/STA
reset replay is unchanged because the helper still returns &vif->bss_conf
for the legacy link.
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: fix possible NULL-pointer deref in mt7996_mcu_sta_bfer_eht()
mt76_connac_get_eht_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it.
In the Linux kernel, the following vulnerability has been resolved:
drm/vc4: hvs/v3d: Fix null dereference in unbind
The hvs and v3d drivers use dev_get_drvdata(master) in their unbind
functions. Since the vc4-drm gets removed before its dependent drivers
(vc4_hvs/vc4_v3d) the vc4_hvs_unbind/vc4_v3d_unbind functions try to
get drvdata of its master and fails with a null dereference error.
Use the data pointer passed to the unbind functions directly instead of
dev_get_drvdata(master). This avoids using potentially freed memory.
In the Linux kernel, the following vulnerability has been resolved:
amt: re-read skb header pointers after every pull
Several AMT receive and transmit paths cache a pointer into the skb head
(ip_hdr(), ipv6_hdr(), eth_hdr() or the AMT message header) and then call
a helper that can reallocate that head before the cached pointer is used
again. pskb_may_pull(), ip_mc_may_pull(), ipv6_mc_may_pull(),
iptunnel_pull_header(), ip_mc_check_igmp() and ipv6_mc_check_mld() can all
free the old head and move the data, so a pointer taken before the call
dangles afterwards and the later access is a use-after-free of the freed
head.
The affected sites are:
amt_rcv() caches ip_hdr() before amt_parse_type() pulls, then reads
iph->saddr.
amt_dev_xmit() caches ip_hdr()/ipv6_hdr() before ip_mc_check_igmp()/
ipv6_mc_check_mld() and pskb_may_pull(), then reads the group address.
amt_multicast_data_handler() caches eth_hdr() before pskb_may_pull(),
then writes the L2 header.
amt_membership_query_handler() caches the AMT header, the outer and
inner eth_hdr() and ip_hdr() before iptunnel_pull_header() and several
pulls, then reads and writes them.
amt_igmpv3_report_handler() and amt_mldv2_report_handler() cache
ip_hdr()/ipv6_hdr() and the current group record and read the record
count from the report header inside the record loop, across the
*_mc_may_pull() calls.
amt_update_handler() caches ip_hdr() and the AMT membership-update
header before pskb_may_pull(), iptunnel_pull_header(),
ip_mc_check_igmp() and the report handler, then reads iph->daddr and
amtmu->nonce / amtmu->response_mac.
Fix each site by either snapshotting the scalar that is used after the
pull before the first pull runs, or re-deriving the header pointer from
the skb after the last pull that can move the head. Values that are
stable across the pull (source and group address, the response MAC and
nonce, the record count, the outer source MAC) are snapshotted; pointers
that are written through or read repeatedly are re-derived.
In the Linux kernel, the following vulnerability has been resolved:
net: hsr: fix memory leak on slave unregistration by removing synced VLANs
When an HSR master device is brought UP, it auto-adds VLAN 0 via
vlan_vid0_add(), which propagates VID 0 to its slave devices (slave A and B).
If a slave device is later unregistered while HSR is active (e.g., during
netns cleanup or interface destruction), hsr_del_port() is called to
detach the slave port from the HSR master. However, hsr_del_port() currently
does not delete the VLAN IDs that were synced to the slave device by HSR.
As a result, the slave device retains a refcount on VID 0 (and any other
synced VLANs). When the slave device is destroyed, its vlan_info /
vlan_vid_info structure remains allocated, leading to a memory leak.
Fix this by calling vlan_vids_del_by_dev(port->dev, master->dev) in
hsr_del_port() before unlinking slave A or slave B ports, matching the
propagation logic in hsr_ndo_vlan_rx_add_vid() / hsr_ndo_vlan_rx_kill_vid()
and the cleanup behavior in bonding and team drivers.
In the Linux kernel, the following vulnerability has been resolved:
sctp: auth: verify auth requirement when auth_chunk is NULL
sctp_auth_chunk_verify() returns true unconditionally when
chunk->auth_chunk is NULL, silently skipping authentication.
This is incorrect when:
1. skb_clone() failed in the BH receive path, leaving auth_chunk
NULL. In sctp_endpoint_bh_rcv() asoc is NULL for new
connections, so the early sctp_auth_recv_cid() check cannot
catch this.
2. No AUTH chunk precedes COOKIE-ECHO, so skb_clone() is never
called and auth_chunk remains NULL.
Fix by checking sctp_auth_recv_cid() when auth_chunk is NULL:
if authentication is required, return false to drop the chunk;
otherwise continue normally.
In the Linux kernel, the following vulnerability has been resolved:
vmxnet3: fix BUG_ON in vmxnet3_get_hdr_len() for Geneve packets
vmxnet3_get_hdr_len() assumes gdesc->rcd.v4/v6/tcp always describe the
outer header, but for a Geneve-encapsulated packet the device can set
them based on the inner header instead, signalled by the
VMXNET3_RCD_HDR_INNER_SHIFT bit in the completion descriptor. Since the
function never skips the outer encapsulation, this mismatch triggers:
- BUG_ON(hdr.ipv4->protocol != IPPROTO_TCP), because the outer
protocol is UDP (Geneve), not TCP.
- BUG_ON(hdr.eth->h_proto != ...), when the tunnel's outer and inner
IP versions differ (e.g. outer IPv6/inner IPv4 or vice versa).
Check VMXNET3_RCD_HDR_INNER_SHIFT up front and bail out, since the
function cannot locate the inner header it would need to parse. Also
convert the remaining BUG_ON()s in this function to return 0
defensively.
In the Linux kernel, the following vulnerability has been resolved:
drm/xe/vm: Fix SVM leak on resv obj alloc failure in xe_vm_create()
Commit 9e9787414882 ("drm/xe/userptr: replace xe_hmm with gpusvm") made
xe_svm_init() unconditional in xe_vm_create() and extended it to also
initialize a "simple" gpusvm state for non-fault-mode VMs. The matching
xe_svm_fini() call in xe_vm_close_and_put() was updated to run
unconditionally, but the error unwind path in xe_vm_create() was not.
On the drm_gpuvm_resv_object_alloc() failure path, xe_svm_init() has
already succeeded but xe_svm_fini() is only called when
XE_VM_FLAG_FAULT_MODE is set. For non-fault-mode VMs this leaves
vm->svm.gpusvm partially initialized and leaks the resources allocated
by drm_gpusvm_init().
For fault-mode VMs, xe_svm_init() additionally acquires the pagemap
owner via drm_pagemap_acquire_owner() and the pagemaps via
xe_svm_get_pagemaps(). Those resources are released by xe_svm_close(),
not xe_svm_fini(). On the same error path, xe_svm_close() is not
called either, so fault-mode VMs leak the pagemap owner and pagemaps.
Fix both leaks:
- Call xe_svm_fini() unconditionally on the err_svm_fini path, matching
the unconditional xe_svm_init() call. Move the vm->size = 0
assignment out of the conditional so the xe_vm_is_closed() assert in
xe_svm_fini() (and xe_svm_close()) holds for both modes.
- Call xe_svm_close() for fault-mode VMs before xe_svm_fini(), matching
the ordering used in xe_vm_close_and_put().
(cherry picked from commit ca2a3587d577ba764e0fe628fb676244fc33ddd4)
In the Linux kernel, the following vulnerability has been resolved:
tipc: fix u16 MTU truncation in media and bearer MTU validation
Both TIPC_NL_MEDIA_SET and TIPC_NL_BEARER_SET accept user-supplied
MTU values but only enforce a minimum bound, not a maximum. When a user
sets the MTU to a value exceeding U16_MAX (65535), it passes validation
but is silently truncated when assigned to u16 fields l->mtu and
l->advertised_mtu in tipc_link_create(). Values like 65536 (0x10000)
truncate to 0, causing a division by zero in tipc_link_set_queue_limits()
which computes TIPC_MAX_PUBL / (l->mtu / ITEM_SIZE). Other overflowing
values (e.g. 65537-131071) produce small incorrect MTU values, resulting
in link malfunction behaviors.
Crash stack (triggered as unprivileged user via user namespace):
tipc_link_set_queue_limits net/tipc/link.c:2531
tipc_link_create net/tipc/link.c:520
tipc_node_check_dest net/tipc/node.c:1279
tipc_disc_rcv net/tipc/discover.c:252
tipc_rcv net/tipc/node.c:2129
tipc_udp_recv net/tipc/udp_media.c:392
Two independent paths lack the upper bound check:
1. tipc_udp_mtu_bad() -- called from __tipc_nl_media_set() (MEDIA_SET)
2. inline check in __tipc_nl_bearer_set() at bearer.c:1160 (BEARER_SET)
Fix both by rejecting MTU values above U16_MAX.
In the Linux kernel, the following vulnerability has been resolved:
net: gre: fix lltx regression for GRE tunnels with SEQ/CSUM
Before commit 00d066a4d4ed ("netdev_features: convert NETIF_F_LLTX to
dev->lltx"), NETIF_F_LLTX was set unconditionally in both
__gre_tunnel_init() and ip6gre_tnl_init_features() alongside
GRE_FEATURES:
dev->features |= GRE_FEATURES | NETIF_F_LLTX;
When that commit converted NETIF_F_LLTX to the dev->lltx flag, it
placed 'dev->lltx = true' after the SEQ/CSUM early returns instead
of before them. This causes GRE/GRETAP/ip6gre tunnels with SEQ or
CSUM+encap to lose lockless TX, reintroducing _xmit_lock acquisition
around their ndo_start_xmit. Since GRE xmit re-enters the stack via
ip_tunnel_xmit(), holding _xmit_lock risks ABBA deadlock with the
underlay device.
CPU0 CPU1
---- ----
lock(&qdisc_xmit_lock_key#6);
lock(&qdisc_xmit_lock_key#3);
lock(&qdisc_xmit_lock_key#6);
lock(&qdisc_xmit_lock_key#3);
Fix by moving dev->lltx = true before the early returns in both
functions, restoring the original unconditional behavior.
In the Linux kernel, the following vulnerability has been resolved:
LoongArch: BPF: Zero-extend signed ALU32 div/mod results
ALU32 operations write a 32-bit result and leave the upper 32 bits of
the BPF register zero. The LoongArch JIT sign-extends the result of
signed ALU32 BPF_DIV and BPF_MOD (off=1), so a negative 32-bit quotient
or remainder leaves bits 63:32 set in JITted code while the verifier
and interpreter model those bits as zero.
Keep sign-extension on the operands, which signed divide needs, and
zero-extend the ALU32 result after the divide or modulo instruction,
matching the unsigned ALU32 div/mod paths and every other ALU32
operation in this JIT.
In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: restrict socket creation to the initial network namespace
QRTR keeps its entire port and node state in module-global variables
that are not partitioned per network namespace: qrtr_local_nid is a
single global node id (always 1) and qrtr_ports is a single global
xarray. qrtr_port_lookup() and qrtr_local_enqueue() operate on that
global state with no network-namespace check, and qrtr_create() places
no restriction on the namespace a socket is created in.
As a result an unprivileged process that creates an AF_QIPCRTR socket
in a separate network namespace, e.g. via
unshare(CLONE_NEWUSER | CLONE_NEWNET), can send QRTR datagrams -
including control-plane messages such as QRTR_TYPE_NEW_SERVER - to QRTR
sockets owned by another namespace, and vice versa. The receiving
socket sees such a message as coming from node id 1, indistinguishable
from a legitimate local client, breaking the isolation that network
namespaces are expected to provide.
QRTR is a transport to global hardware endpoints (the modem and other
remote processors) and has no per-namespace semantics; its in-kernel
name service already creates its socket in init_net only. Confine the
socket family to the initial network namespace, as other
non-namespace-aware socket families do (see llc_ui_create() and the
ieee802154 socket code).
In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix MCIA register buffer overflow on 32 dword reads
The MCIA register can return up to 32 dwords (128 bytes) when the device
advertises the mcia_32dwords capability, but struct
mlx5_ifc_mcia_reg_bits only defines dword_0..11, leaving room for just
12 dwords (48 bytes) of data.
mlx5_query_mcia() clamps the read size to mlx5_mcia_max_bytes() and then
memcpy()s that many bytes out of the register, potentially reading past
the end of the 'out' buffer. On kernels built with FORTIFY_SOURCE this
is caught as a buffer overflow while reading the module EEPROM via
ethtool:
detected buffer overflow in memcpy
kernel BUG at lib/string_helpers.c:1048!
RIP: 0010:fortify_panic+0x13/0x20
Call Trace:
mlx5_query_mcia.isra.0+0x200/0x210 [mlx5_core]
mlx5_query_module_eeprom_by_page+0x4a/0xa0 [mlx5_core]
mlx5e_get_module_eeprom_by_page+0xbb/0x120 [mlx5_core]
eeprom_prepare_data+0xf3/0x170
ethnl_default_doit+0xf1/0x3b0
Extend the mcia_reg layout to 32 dwords.
In the Linux kernel, the following vulnerability has been resolved:
ice: prevent tstamp ring allocation for non-PF VSI types
The pf->txtime_txqs bitmap tracks which Tx queues have ETF (Earliest
TxTime First) offload enabled. This bitmap is indexed by queue number
and is set by ice_offload_txtime(), which only operates on PF VSI
queues.
However, ice_is_txtime_ena() does not check the VSI type before
consulting the bitmap. When ETF offload is enabled on PF Tx queue 0,
bit 0 is set in pf->txtime_txqs. During a subsequent PCI reset
rebuild, the CTRL VSI's Tx queue 0 is reconfigured and
ice_is_txtime_ena() is called for that ring. Since it only checks
pf->txtime_txqs by queue index without distinguishing VSI type, it
finds bit 0 set and returns true, matching the PF VSI's ETF queue,
not the CTRL VSI's. This causes ice_vsi_cfg_txq() to spuriously
allocate a tstamp_ring for the CTRL VSI ring.
Since CTRL VSI rings have no associated netdev, ice_clean_tx_ring()
takes an early return at the !netdev check before reaching
ice_free_tx_tstamp_ring(), leaking the allocation. Each PCI reset
leaks one 64-byte tstamp_ring.
Fix this by restricting ice_is_txtime_ena() to return true only for
PF VSI rings, since txtime_txqs is only meaningful for PF VSI queues.
In the Linux kernel, the following vulnerability has been resolved:
rds: tcp: unregister sysctl before tearing down listen socket
rds_tcp_exit_net() frees the per-netns RDS TCP listen socket via
rds_tcp_kill_sock() before unregistering the per-netns sysctl table. Since
rds_tcp_skbuf_handler() derives the netns from
rtn->rds_tcp_listen_sock->sk, a concurrent sysctl write can race with
netns teardown and dereference the freed socket/sk.
KASAN reports the race as:
BUG: KASAN: slab-use-after-free in rds_tcp_skbuf_handler+0x2aa/0x2e0
rds_tcp_skbuf_handler net/rds/tcp.c:721
proc_sys_call_handler fs/proc/proc_sysctl.c
vfs_write fs/read_write.c
__x64_sys_pwrite64 fs/read_write.c
Fix this by unregistering the RDS TCP sysctl table before calling
rds_tcp_kill_sock(). unregister_net_sysctl_table() prevents new sysctl
handlers from starting and waits for in-flight handlers to finish, so
the listen socket can then be released safely. The fix was tested
against the linked reproducer.
In the Linux kernel, the following vulnerability has been resolved:
tipc: fix integer overflow in tipc_recvmsg() and tipc_recvstream()
In tipc_recvmsg(), the copy length is computed as:
copy = min_t(int, dlen - offset, buflen);
buflen is size_t but min_t(int, ...) casts it to int. When buflen
exceeds INT_MAX (e.g. 0xFFFFFFFF via io_uring provided buffers), it
wraps negative, wins the comparison, and the negative copy length
propagates to simple_copy_to_iter() where int-to-size_t promotion
makes it SIZE_MAX, triggering a WARN_ON. tipc_recvstream() has the
same pattern.
Kernel panic - not syncing: kernel: panic_on_warn set ...
RIP: 0010:simple_copy_to_iter+0x9e/0xd0 (net/core/datagram.c:521)
Call Trace:
__skb_datagram_iter+0x123/0x8b0 (net/core/datagram.c:402)
skb_copy_datagram_iter+0x77/0x1a0 (net/core/datagram.c:534)
tipc_recvmsg+0x3d7/0xe80 (net/tipc/socket.c:1934)
io_recvmsg+0x47e/0xda0
Fix by changing min_t(int, ...) to min_t(size_t, ...) in both
functions. The result is always <= (dlen - offset), which is bounded
by TIPC maximum message size (0x1ffff bytes), so the implicit
narrowing on assignment to int copy is always safe.
In the Linux kernel, the following vulnerability has been resolved:
net: drop_monitor: fix info leak in NET_DM_ATTR_PAYLOAD
net_dm_packet_report_fill() and net_dm_hw_packet_report_fill() open code
the NET_DM_ATTR_PAYLOAD attribute to avoid zeroing the packet payload
before overwriting it with skb_copy_bits().
skb_put() reserves nla_total_size(payload_len), i.e. the header plus the
NLA_ALIGN() padding, but only payload_len bytes are copied in. When
payload_len is not a multiple of 4 the 1-3 padding bytes are never
initialized and are leaked to user space inside the netlink message.
KMSAN confirms the leak for the software path when the packet payload
length is not 4-byte aligned:
BUG: KMSAN: kernel-infoleak in _copy_to_iter
_copy_to_iter
__skb_datagram_iter
skb_copy_datagram_iter
netlink_recvmsg
sock_recvmsg
__sys_recvfrom
Uninit was created at:
kmem_cache_alloc_node_noprof
__alloc_skb
net_dm_packet_work
Bytes 173-175 of 176 are uninitialized
Use __nla_reserve(), which sets up the attribute header and zeroes the
padding, instead of open coding the attribute construction.
In the Linux kernel, the following vulnerability has been resolved:
drop_monitor: fix size calculations for 64-bit attributes
net_dm_packet_report_fill() and net_dm_hw_packet_report_fill() use
nla_put_u64_64bit() to append 64-bit attributes (NET_DM_ATTR_PC and
NET_DM_ATTR_TIMESTAMP).
On 32-bit architectures without CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS,
nla_put_u64_64bit() may append a 4-byte NET_DM_ATTR_PAD attribute for
64-bit alignment.
However, net_dm_packet_report_size() and net_dm_hw_packet_report_size()
used nla_total_size(sizeof(u64)) instead of nla_total_size_64bit(sizeof(u64)),
budgeting 12 bytes instead of up to 16 bytes.
This under-estimation of SKB size can lead to an skb_over_panic() when
__nla_reserve() or skb_put() is subsequently called.
Fix this by using nla_total_size_64bit(sizeof(u64)) in both size calculations.
In the Linux kernel, the following vulnerability has been resolved:
drop_monitor: perform u64_stats updates under IRQ-disabled section
In net_dm_packet_trace_kfree_skb_hit() and net_dm_hw_trap_packet_probe(),
u64_stats_update_begin() / u64_stats_inc() / u64_stats_update_end() were
called after spin_unlock_irqrestore(&...drop_queue.lock, flags), when local
IRQs had already been re-enabled.
Tracepoint probes can execute in IRQ or softirq context. On 32-bit
architectures, u64_stats_update_begin() disables preemption but not interrupts,
relying on seqcount writes. If a nested interrupt occurs on the same CPU during
the 64-bit stats update, the reentrant seqcount update can corrupt the
seqcount state or stats value.
Fix this by performing the 64-bit per-CPU stats update before releasing
drop_queue.lock via spin_unlock_irqrestore(), ensuring local interrupts remain
disabled during the u64_stats update.
In the Linux kernel, the following vulnerability has been resolved:
LoongArch: BPF: Fix memory leak in bpf_jit_free()
When bpf_int_jit_compile() is called for subprograms, it returns early
during the first pass (!prog->is_func || extra_pass is false), keeping
ctx->offset alive for the subsequent extra pass.
If JIT compilation fails for a later subprogram, the BPF core aborts and
calls bpf_jit_free() to clean up the first subprogram. However,
bpf_jit_free() fails to free jit_data->ctx.offset, which causes a memory
leak of the JIT context offsets array.
So fix this by adding the missing kvfree(jit_data->ctx.offset) in
bpf_jit_free().
In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Fix cork use-after-free in tcp_bpf_sendmsg()
tcp_bpf_sendmsg() keeps msg_tx across sk_stream_wait_memory(), which
drops and reacquires the socket lock. Its error path tries to decide
whether msg_tx names the local temporary message by comparing it with
the current value of psock->cork.
This comparison is unsafe when two threads send on the same socket:
Thread A Thread B
msg_tx = psock->cork
sk_msg_alloc() fails
sk_stream_wait_memory()
releases the socket lock acquires the socket lock
completes the cork
psock->cork = NULL
frees the cork
reacquires the socket lock
msg_tx != psock->cork
sk_msg_free(msg_tx)
The stale cork is therefore mistaken for the local temporary message
and freed again. KASAN reported:
BUG: KASAN: slab-use-after-free in sk_msg_free+0x49/0x50
Read of size 4 at addr ffff88810c908800 by task poc/90
Call Trace:
sk_msg_free+0x49/0x50
tcp_bpf_sendmsg+0x14f5/0x1cc0
__sys_sendto+0x32c/0x3a0
__x64_sys_sendto+0xdb/0x1b0
Allocated by task 89:
__kasan_kmalloc+0x8f/0xa0
tcp_bpf_sendmsg+0x16b3/0x1cc0
Freed by task 91:
__kasan_slab_free+0x43/0x70
kfree+0x131/0x3c0
tcp_bpf_sendmsg+0xec3/0x1cc0
msg_tx can only name the stack-local tmp or the shared cork. Check for
tmp directly so a changed psock->cork cannot turn a shared message into
an apparent local one.
In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix use-after-free freeing trigger private data
Commit 61d445af0a7c ("tracing: Add bulk garbage collection of freeing
event_trigger_data") moved the kfree() of event_trigger_data to a kthread
that runs tracepoint_synchronize_unregister() before freeing. That removed
the synchronization the trigger .free callbacks used to get implicitly and
inline from trigger_data_free().
event_hist_trigger_free(), event_hist_trigger_named_free() and
event_enable_trigger_free() free their satellite data (hist_data, cmd_ops,
enable_data) right after trigger_data_free() returns. With the
synchronization now deferred to the kthread, a concurrent tracepoint
handler can still reach that data through the list_del_rcu()'d trigger,
causing a use-after-free.
The histogram teardown must stay synchronous: remove_hist_vars() and
unregister_field_var_hists() have to detach a synthetic event from the
histogram before the trigger-removal write returns, otherwise a following
command races in and the synthetic-event removal fails with -EBUSY, as the
trigger-synthetic-eprobe.tc selftest catches. Make those callbacks wait
with the correct barrier - tracepoint_synchronize_unregister(), matching
the free kthread - before freeing.
The enable trigger has no such synchronous requirement, and a blocking
synchronize there would re-serialize the path that commit deliberately
deferred. Give it an optional private_data_free() callback that the free
kthread runs after its grace period, and free enable_data from there.
In the Linux kernel, the following vulnerability has been resolved:
drm/rockchip: analogix_dp: Add missing error check for platform_get_resource()
Add missing error check for platform_get_resource() return value to
prevent NULL pointer dereference when memory resource is not available.
In the Linux kernel, the following vulnerability has been resolved:
drm/imagination: Count paired job fence as dependency in prepare_job()
The DRM scheduler's prepare_job() callback counts the remaining
non-signaled native dependencies for a job, preventing job submission
until those (plus job data and fence update) can fit in the job queue's
CCCB.
This means checking which dependencies can be waited upon in the
firmware, i.e. whether they are backed by a UFO object, i.e. whether
their drm_sched_fence::parent has been assigned to a
pvr_queue_fence::base fence. That happens when the job owning the fence
is submitted to the firmware.
Paired geometry and fragment jobs are submitted at the same time, which
means the dependency between them can't be checked this way before
submission.
Update job_count_remaining_native_deps() to take into account the
dependency between paired jobs.
This fixes cases where prepare_job() underestimated the space left in
an almost full fragment CCCB, wrongly unblocking run_job(), which then
returned early without writing the full sequence of commands to the
CCCB.
The above lead to kernel warnings such as the following and potentially
job timeouts (depending on waiters on the missing commands):
[ 375.702979] WARNING: drivers/gpu/drm/imagination/pvr_cccb.c:178 at pvr_cccb_write_command_with_header+0x2c4/0x330 [powervr], CPU#1: kworker/u16:3/47
[ 375.703160] Modules linked in:
[ 375.703571] CPU: 1 UID: 0 PID: 47 Comm: kworker/u16:3 Tainted: G W 7.0.0-rc2-g817eb6b11ad5 #40 PREEMPT
[ 375.703613] Tainted: [W]=WARN
[ 375.703627] Hardware name: Texas Instruments AM625 SK (DT)
[ 375.703645] Workqueue: powervr-sched drm_sched_run_job_work [gpu_sched]
[ 375.703741] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 375.703764] pc : pvr_cccb_write_command_with_header+0x2c4/0x330 [powervr]
[ 375.703847] lr : pvr_queue_submit_job_to_cccb+0x578/0xa70 [powervr]
[ 375.703921] sp : ffff800084a97650
[ 375.703934] x29: ffff800084a97740 x28: 0000000000000958 x27: ffff80008565d000
[ 375.703979] x26: 0000000000000030 x25: ffff800084a97680 x24: 0000000000001000
[ 375.704017] x23: ffff800084a97820 x22: 1ffff00010952ecc x21: 0000000000000008
[ 375.704056] x20: 00000000000006a8 x19: ffff00002ff7da88 x18: 0000000000000000
[ 375.704093] x17: 0000000020020000 x16: 0000000000020000 x15: 0000000000000000
[ 375.704132] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
[ 375.704168] x11: 000000000000f2f2 x10: 00000000f3000000 x9 : 00000000f3f3f3f3
[ 375.704206] x8 : 00000000f2f2f200 x7 : ffff700010952ecc x6 : 0000000000000008
[ 375.704243] x5 : 0000000000000000 x4 : 1ffff00010acba00 x3 : 0000000000000000
[ 375.704279] x2 : 0000000000000007 x1 : 0000000000000fff x0 : 000000000000002f
[ 375.704317] Call trace:
[ 375.704331] pvr_cccb_write_command_with_header+0x2c4/0x330 [powervr] (P)
[ 375.704411] pvr_queue_submit_job_to_cccb+0x578/0xa70 [powervr]
[ 375.704487] pvr_queue_run_job+0x3a4/0x990 [powervr]
[ 375.704562] drm_sched_run_job_work+0x580/0xd48 [gpu_sched]
[ 375.704623] process_one_work+0x520/0x1288
[ 375.704658] worker_thread+0x3f0/0xb3c
[ 375.704680] kthread+0x334/0x3d8
[ 375.704706] ret_from_fork+0x10/0x20
[ 375.704736] ---[ end trace 0000000000000000 ]---
In the Linux kernel, the following vulnerability has been resolved:
drm/bridge: cdns-dsi: Replace deprecated UNIVERSAL_DEV_PM_OPS()
The deprecated UNIVERSAL_DEV_PM_OPS() macro uses the provided callbacks
for both runtime PM and system sleep. This causes the DSI clocks to be
disabled twice: once during runtime suspend and again during system
suspend, resulting in a WARN message from the clock framework when
attempting to disable already-disabled clocks.
[ 84.384540] clk:231:5 already disabled
[ 84.388314] WARNING: CPU: 2 PID: 531 at /drivers/clk/clk.c:1181 clk_core_disable+0xa4/0xac
...
[ 84.579183] Call trace:
[ 84.581624] clk_core_disable+0xa4/0xac
[ 84.585457] clk_disable+0x30/0x4c
[ 84.588857] cdns_dsi_suspend+0x20/0x58 [cdns_dsi]
[ 84.593651] pm_generic_suspend+0x2c/0x44
[ 84.597661] ti_sci_pd_suspend+0xbc/0x15c
[ 84.601670] dpm_run_callback+0x8c/0x14c
[ 84.605588] __device_suspend+0x1a0/0x56c
[ 84.609594] dpm_suspend+0x17c/0x21c
[ 84.613165] dpm_suspend_start+0xa0/0xa8
[ 84.617083] suspend_devices_and_enter+0x12c/0x634
[ 84.621872] pm_suspend+0x1fc/0x368
To address this issue, replace UNIVERSAL_DEV_PM_OPS() with
RUNTIME_PM_OPS(). Bridge and panel drivers should only deal with runtime
PM, as the DRM framework manages system-wide power transitions through
the bridge enable() and disable() hooks.
In the Linux kernel, the following vulnerability has been resolved:
drm/dp/mst: fix OOB reads in remote DPCD/I2C sideband reply parsers
drm_dp_sideband_parse_remote_dpcd_read() reads num_bytes from the raw
message and then unconditionally does:
memcpy(bytes, &raw->msg[idx], num_bytes);
without checking that idx + num_bytes <= raw->curlen. raw->msg[] is
256 bytes; if a malicious or misbehaving MST hub sets num_bytes larger
than the remaining payload, the memcpy reads past the received data
into whatever follows in raw->msg[].
drm_dp_sideband_parse_remote_i2c_read_ack() has the same flaw (noted
with a /* TODO check */ comment since the code was introduced).
Fix both functions by using a single combined check
(idx + num_bytes > curlen) before each memcpy. Since num_bytes is u8,
it is always >= 0, so this strictly subsumes the simpler idx > curlen
form and no separate step is needed.
[added missing fixes tag]
In the Linux kernel, the following vulnerability has been resolved:
drm/dp/mst: fix buffer overflows in sideband chunk accumulation
drm_dp_sideband_append_payload() has three related bugs when processing
device-provided sideband reply data:
1. Zero-length curchunk_len underflow: msg_len is a 6-bit field taken
directly from the DP sideband header. If a device sends msg_len=0,
curchunk_len is set to zero. The condition (curchunk_idx >= curchunk_len)
is immediately true, and curchunk_len-1 wraps to 255 (u8 underflow).
drm_dp_msg_data_crc4() reads 255 bytes from chunk[48], then memcpy()
writes 255 bytes into msg[], both far out of bounds.
2. chunk[48] overflow: curchunk_len can reach 63 (6-bit field). chunk[] is
only 48 bytes. Multi-iteration payload assembly appends 16-byte blocks
until curchunk_idx reaches curchunk_len, writing up to 15 bytes past
the end of chunk[] into msg[].
3. msg[256] overflow: each chunk contributes (curchunk_len-1) bytes to
msg[]. No check ensures curlen + (curchunk_len-1) stays within msg[256],
so the memcpy can spill into adjacent struct fields.
All three are reachable from any DP MST device that can forge sideband
reply messages on a physical connection.
In the Linux kernel, the following vulnerability has been resolved:
drm/dp/mst: fix OOB reads on 2-byte fields in sideband reply parsers
Three sideband reply parsers read 16-bit fields as:
val = (raw->msg[idx] << 8) | (raw->msg[idx+1]);
and check bounds only after the fact. When idx == raw->curlen,
raw->msg[idx+1] reads one byte past the received message data into
the following struct fields (curchunk_len, curchunk_idx, curlen).
Affected functions:
- drm_dp_sideband_parse_enum_path_resources_ack()
full_payload_bw_number and avail_payload_bw_number fields
- drm_dp_sideband_parse_allocate_payload_ack()
allocated_pbn field
- drm_dp_sideband_parse_query_payload_ack()
allocated_pbn field
Fix by using a single combined check (idx + 2 > curlen) before each
2-byte read. Since the check is strictly tighter than idx > curlen,
no separate step is needed.
[added fixes tag]
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx: fix cleaner shader IB buffer overflow
The cleaner shader sysfs path allocates a 16-dword (64 byte) IB but
incorrectly fills (align_mask + 1) dwords. On GFX rings align_mask is
0xff, so the loop wrote 256 dwords into a 64-byte buffer, causing a
kernel page fault.
The IB only needs to be a minimal NOP shell to schedule the job; the
cleaner shader itself is emitted on the ring via emit_cleaner_shader().
Fill 16 dwords to match the allocation.
v2: Use ib_size_dw variable (Lijo)
(cherry picked from commit bf21af331ebf72d0935fd70c73192414a422c03a)
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: check amdgpu_vm_bo_find() result in GET_MAPPING_INFO
The AMDGPU_GEM_OP_GET_MAPPING_INFO path of amdgpu_gem_op_ioctl() looks
up the bo_va for the buffer object in the caller's VM via
amdgpu_vm_bo_find(), but uses the returned pointer without checking it.
amdgpu_vm_bo_find() returns NULL when the BO has no bo_va in that VM,
which is the normal case for a BO that has never been mapped. The result
is fed straight into amdgpu_vm_bo_va_for_each_valid_mapping(), which
expands to list_for_each_entry(mapping, &(bo_va)->valids, list) and
dereferences bo_va, causing a NULL pointer dereference.
This is reachable by any process able to issue the ioctl (render group)
simply by requesting mapping info for an unmapped BO.
Return -ENOENT when no bo_va is found, jumping to out_exec so the
drm_exec context and GEM object reference are released.
(cherry picked from commit 528b19377affc1cc7362a70a254c1dda793595f9)
In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Fix buffer overflow in steered register list allocation
The size calculation for the steered register extarray uses only the
geometry DSS mask (g_dss_mask) to determine the number of entries to
allocate:
total = bitmap_weight(gt->fuse_topo.g_dss_mask, ...) * steer_reg_num;
However, the filling loop uses for_each_dss_steering(), which iterates
over for_each_dss(), defined as the union of g_dss_mask and c_dss_mask
(geometry + compute DSS). On platforms with compute-only DSS bits, the
loop writes past the allocated buffer, corrupting adjacent slab objects.
This manifests as list_del corruption and SLUB redzone overwrites during
drm_managed_release on device unbind, since the overflow corrupts the
drmres list_head of neighboring allocations.
Fix by computing the allocation size using the union of both DSS masks,
matching the iteration pattern of for_each_dss_steering().
--
v2:
- use bitmap_weighted_or() (Zhanjun)
(cherry picked from commit 0a78a44f4901aa6c9263e66be7fce02282f1109f)
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix context pstate override handling
There are several problems in the context pstate handling code.
The most serious ones are potential use-after-free and NULL pointer
dereferences at context initialization time. Both are due
amdgpu_ctx_init() not holding the adev->pm.stable_pstate_ctx_lock, which
is otherwise used from both sysfs and the context code itself for
modifying and clearing the stored context pointer.
Second issue is that context fini can trample over the pstate
configuration set via sysfs. This is due the restore state
(ctx->stable_pstate) being saved at context init time, and not if, or when
the context actually changes the pstate. As the context exits it will
therefore incorrectly restore to what was set before the sysfs override
was requested.
The simplest fix is to drastically simplify how the state is tracked, by
clearly defining the points at which pstate ownership is taken and
released, and to handle all transitions under the correct lock.
Instead of at context init time, the previous state is saved only at the
point the context overrides the current state, and is restored on context
exit only if the context is still the owner of the current override state.
(cherry picked from commit 1b5e413713c0a93bc1818394d0ce49aaad21bd27)
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: validate CP_GFX_SHADOW chunk size in CS pass1
Add a minimum-length check for the AMDGPU_CHUNK_ID_CP_GFX_SHADOW chunk in
amdgpu_cs_pass1(), matching the gate already present for the IB, FENCE and
BO_HANDLES chunk types.
The CP_GFX_SHADOW case previously shared a bare break with the dependency
and syncobj chunk types, which do not dereference a fixed-size struct. When
userspace submits this chunk with length_dw == 0, vmemdup_array_user() is
called with size 0 and returns ZERO_SIZE_PTR, which passes the IS_ERR()
check. amdgpu_cs_p2_shadow() then dereferences chunk->kdata as a struct
drm_amdgpu_cs_chunk_cp_gfx_shadow (reading shadow->flags), faulting on the
ZERO_SIZE_PTR and causing a NULL-pointer dereference.
This is reachable by an unprivileged process in the render group. Reject
undersized chunks with -EINVAL during pass1 so the bad submission is
rejected before pass2 ever dereferences the data.
(cherry picked from commit 7f61b2eef7415eccdb40850aca0de94211948657)
In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau: fix reversed error cleanup order in ucopy functions
nouveau_uvmm_vm_bind_ucopy() and nouveau_exec_ucopy() place their error
cleanup labels in allocation order rather than reverse allocation order.
On a u_memcpya() failure for in_sync.s, the goto to err_free_ops (or
err_free_pushs) frees the first allocation and then falls through to
err_free_ins, which calls u_free() on args->in_sync.s.
Since args->in_sync.s still holds the ERR_PTR returned by the failed
u_memcpya(), and ERR_PTR values are not caught by ZERO_OR_NULL_PTR(),
kvfree() proceeds to dereference it, which can result in a kernel oops.
A failure for out_sync.s instead jumps to err_free_ins and skips freeing
the first allocation, leading to a memory leak.
Fix by swapping the cleanup label order so resources are freed in the
correct reverse allocation sequence.